Yamaha FZ6RZ(C) Скачать руководство пользователя страница 88

Страница: 88 / 114

PERIODIC MAINTENANCE AND ADJUSTMENT

7-41

EAU25080

Rear wheel

EAU34414

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the locknut and drive chain

slack adjusting nut on each side of
the swingarm.

2. Loosen the axle nut.

3. Lift the rear wheel off the ground

according to the procedure on
page 7-39.

4. Remove the axle nut.
5. Push the wheel forward, and then

remove the drive chain from the
rear sprocket.

TIP

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain does not need to
be disassembled in order to re-
move and install the rear wheel.

6. While supporting the brake caliper

and slightly lifting the wheel, pull
the wheel axle out.

TIP

A rubber mallet may be useful to tap the
wheel axle out.

7. Remove the wheel.

NOTICE:

not apply the brake after the
wheel has been removed to-
gether with the brake disc, oth-
erwise the brake pads will be
forced shut.

[ECA11071]

1. Axle nut

2. Drive chain slack adjusting nut
3. Locknut

1. Locknut
2. Drive chain slack adjusting nut

3. Brake caliper bracket

4. Brake caliper
5. Wheel axle

U36P11E0.book Page 41 Tuesday, September 29, 2009 5:12 PM

Содержание FZ6RZ(C)



















































































































Результаты поиска

Содержание FZ6RZ(C)

Отзывы:

Yamaha FZ6RZ(C), Руководство пользователя, Страница: 88 / 114

Результаты поиска

Содержание FZ6RZ(C)

Отзывы: