Yamaha FZ6-NV Скачать руководство пользователя | Manualshive

Страница: 78 / 90

background image

MOTORCYCLE CARE AND STORAGE

7-1

EAU26040

Care

While the open design of a motorcycle
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un-
noticed on a car, however, it detracts
from the overall appearance of a motor-
cycle. Frequent and proper care does
not only comply with the terms of the
warranty, but it will also keep your
motorcycle looking good, extend its life
and optimize its performance.

Before cleaning

1. Cover the muffler outlets with plas-

tic bags after the engine has
cooled down.

2. Make sure that all caps and covers

as well as all electrical couplers
and connectors, including the
spark plug caps, are tightly in-
stalled.

3. Remove extremely stubborn dirt,

like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-

ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and de-
greaser off with water.

Cleaning

CAUTION:

ECA10770

●

Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.

●

Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge
with mild detergent and water to
clean plastic.

●

Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive

cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

●

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

●

For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.

U1B322E0.book Page 1 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
76
77
78
79
80
...
»

Содержание FZ6-NV



























































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6-NV

Бренд: HRC Страницы: 88

Бренд: GAS GAS Страницы: 150

Бренд: Honda Страницы: 243

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 124

ROAD STAR XV16A

Бренд: Yamaha Страницы: 117

X MAX CZD300P 2022

Бренд: Yamaha Страницы: 142

Бренд: Yamaha Страницы: 97

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 96

Бренд: Bajaj Страницы: 319

Бренд: DYNATEK Страницы: 5

Бренд: Aim Страницы: 47

Бренд: hepco & becker Страницы: 3

Бренд: IBEX Страницы: 3

Бренд: HealTech Electronics Страницы: 2

Бренд: Healtech Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды