Yamaha FZ6-NV Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 90

Yamaha FZ6-NV Скачать руководство пользователя страница 35

PRE-OPERATION CHECKS

4-2

4

EAU15603

Pre-operation check list

ITEM

CHECKS

PAGE

Fuel

• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.

Engine oil

• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.

Coolant

• Check coolant level in reservoir.
• If necessary, add recommended coolant to specified level.
• Check cooling system for leakage.

Front brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Rear brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Clutch

• Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary.

U1B322E0.book Page 2 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
33
34
35
36
37
...
»

Содержание FZ6-NV



























































































Отзывы:

Нет отзывов