manualshive.com logo in svg

Yamaha FZ6-NV, Руководство пользователя

Поделиться
Скачать
Yamaha FZ6-NV Скачать руководство пользователя страница 26

INSTRUMENT AND CONTROL FUNCTIONS

3-10

3

EAU12870

Shift pedal 

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 6-speed con-
stant-mesh transmission equipped on
this motorcycle.

EAU26822

Brake lever 

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

The brake lever is equipped with a po-
sition adjusting dial. To adjust the dis-
tance between the brake lever and the
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure that
the appropriate setting on the adjusting
dial is aligned with the “

” mark on the

brake lever.

EAU12941

Brake pedal 

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

1. Shift pedal

1. Brake lever

2. Brake lever position adjusting dial

3. “

” mark

4. Distance between brake lever and handlebar 

grip

1. Brake pedal

U1B322E0.book  Page 10  Monday, August 8, 2005  1:49 PM

ProCarManuals.com

Содержание FZ6-NV



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды