Yamaha FZ6-N Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 88

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-19

6

●

Be careful that water does not en-
ter the brake fluid reservoir when
refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.

●

Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.

●

As the brake pads wear, it is nor-
mal for the brake fluid level to grad-
ually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.

EAU22730

Changing the brake fluid

Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addition,
have the oil seals of the master cylin-
ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

●

Oil seals: Replace every two
years.

●

Brake hoses: Replace every four
years.

EAU22760

Drive chain slack

The drive chain slack should be
checked before each ride and adjusted
if necessary.

EAU22770

To check the drive chain slack

1. Place the motorcycle on a level

surface and hold it in an upright po-
sition.

NOTE:

When checking and adjusting the drive
chain slack, the motorcycle should be
positioned straight up and there should
be no weight on it.

2. Shift the transmission into the neu-

tral position.

3. Move the rear wheel by pushing

the motorcycle to locate the tight-
est portion of the drive chain, and
then measure the drive chain slack
as shown.

Drive chain slack:

45.0–55.0 mm (1.77–2.17 in)

U1B3E1E0.book Page 19 Thursday, July 8, 2004 11:49 AM

«
...
55
56
57
58
59
...
»

Содержание FZ6-N

























































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6-N

Бренд: hepco & becker Страницы: 4

Бренд: Big Dog Страницы: 100

Бренд: Yamaha Страницы: 220

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 176

Бренд: kellermann Страницы: 5

Бренд: Ducati Страницы: 27

Бренд: Dynafit Страницы: 48

Бренд: IBEX Страницы: 2

Бренд: Datatool Страницы: 9

Бренд: APRILIA Страницы: 168

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 64

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 114

Бренд: Yamaha Страницы: 119

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды