Yamaha FZ1-NW Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 98

background image

MOTORCYCLE CARE AND STORAGE

7-1

EAU37833

Matte color caution

CAUTION:

ECA15192

Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be-
fore cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored fin-
ished parts.

EAU26011

Care

While the open design of a motorcycle
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un-
noticed on a car, however, it detracts
from the overall appearance of a motor-
cycle. Frequent and proper care does
not only comply with the terms of the
warranty, but it will also keep your
motorcycle looking good, extend its life
and optimize its performance.

Before cleaning

1. Cover the muffler outlet with a

plastic bag after the engine has
cooled down.

2. Make sure that all caps and covers

as well as all electrical couplers
and connectors, including the
spark plug caps, are tightly in-
stalled.

3. Remove extremely stubborn dirt,

like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-

ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and de-
greaser off with water.

Cleaning

CAUTION:

ECA10770

●

Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.

●

Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge
with mild detergent and water to
clean plastic.

●

Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive

U2D121E0.book Page 1 Tuesday, September 19, 2006 1:30 PM

ProCarManuals.com

«
...
84
85
86
87
88
...
»

Содержание FZ1-NW



































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ1-NW

Бренд: GAS GAS Страницы: 57

Бренд: BMW Motorrad Страницы: 143

Бренд: N-Com Страницы: 6

Бренд: Triumph Страницы: 410

Бренд: N-Com Страницы: 2

Бренд: hepco & becker Страницы: 2

Two Fifty 250 cc

Бренд: Mash Страницы: 62

DaVinci RSV4-APRC

Бренд: STARLANE Страницы: 2

Бренд: Corbin Страницы: 4

Бренд: Dakota Digital Страницы: 11

Бренд: Megelli Страницы: 83

Бренд: Sundstrom Страницы: 68

Бренд: Kemppi Страницы: 10

Бренд: MOTO GUZZI Страницы: 48

Бренд: MOTO GUZZI Страницы: 198

2002 California Special Sport

Бренд: MOTO GUZZI Страницы: 155

Бренд: MOTO GUZZI Страницы: 357

Бренд: Shark Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды