Yamaha FL250G страница 76 Скачать руководство пользователя

Страница: 76 / 86

Maintenance

Twin engines

EMU29371

Disconnecting the battery

Turn off the battery cut-off switch (if
equipped) and main switch.

NOTICE:

they are left on, the electrical system
can be damaged.

[ECM01930]

Disconnect the negative cable(s) from
the negative (-) terminal.

NOTICE:

Al-

ways disconnect all negative (-) ca-
bles first to avoid a short circuit and
damage to the electrical system.

[ECM01940]

Disconnect the positive cable(s) and re-
move the battery from the boat.

Clean, maintain, and store the battery ac-
cording to the manufacturer’s instruc-
tions.

1. Starboard side engine

2. Port side engine

3. Red cable
4. Black cable

5. Isolator leads with circuit protection

6. Fuse
7. Battery for starting

8. Battery for accessories

9. Negative connecting cable

ZMU05941

U6DXK0E0.book Page 70 Friday, May 13, 2011 3:08 PM

Содержание FL250G























































































Результаты поиска

Содержание FL250G

Отзывы:

Похожие инструкции для FL250G

Бренды по названию

Популярные бренды

Yamaha FL250G, Руководство пользователя

Результаты поиска

Содержание FL250G

Отзывы:

Похожие инструкции для FL250G

Бренды по названию

Популярные бренды