Yamaha FL250G страница 55 Скачать руководство пользователя | Manualshive

Страница: 55 / 86

background image

Operation

49

3.

Pull the tilt support lever toward you to
support the engine.

WARNING! After

tilting the outboard motor, be sure to
support it with the tilt support knob or
tilt support lever. Otherwise the out-
board motor could fall back down sud-
denly if oil in the power trim and tilt
unit or in the power tilt unit loses pres-
sure.

[EWM00262]

NOTICE:

Do not use the

tilt support lever or knob when traile-
ring the boat. The outboard motor
could shake loose from the tilt support
and fall. If the motor cannot be trail-
ered in the normal running position,
use an additional support device to
secure it in the tilt position. For more
detailed information, see page 52.

[ECM01641]

4.

Once the outboard motor is supported
with the tilt support lever, press the power
trim and tilt switch “

” (down) to retract

the trim rods.

NOTICE:

Make sure that

the trim rods retracts completely dur-
ing mooring. This protects the rods
from marine growth and corrosion,
which could damage the power trim
and tilt mechanism.

[ECM00252]

ZMU04602

UP

ZMU07399

U6DXK0E0.book Page 49 Friday, May 13, 2011 3:08 PM

«
...
53
54
55
56
57
...
»

Содержание FL250G























































































Отзывы:

Нет отзывов

Похожие инструкции для FL250G

Бренд: Abit Страницы: 120

Бренд: Acrosser Technology Страницы: 7

Бренд: JETWAY Страницы: 48

Бренд: Linear Technology Страницы: 10

Бренд: ASROCK Страницы: 56

Бренд: Biostar Страницы: 23

LCD Programmer Module

Бренд: Xtralis VESDA Страницы: 54

Бренд: ECS Страницы: 92

C807MS-E33 Series

Бренд: MSI Страницы: 124

Бренд: ASROCK Страницы: 2

Бренд: TYAN Страницы: 37

SKR Mini E3 V2.0

Бренд: BIGTREETECH Страницы: 10

Бренд: Abit Страницы: 112

Бренд: Gigabyte Страницы: 142

G31MX 2.0 Series

Бренд: Foxconn Страницы: 76

Бренд: Foxconn Страницы: 113

Бренд: Foxconn Страницы: 73

Бренд: Gigabyte Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды