Yamaha FL200C Скачать руководство пользователя страница 33

Страница: 33 / 100

Instruments and indicators

The clock operates on battery power. Dis-
connecting the battery will stop the clock.
Reset the clock after connecting the battery.

EMU36081

Voltmeter

The voltmeter displays the charge of the bat-
tery in volts(V).

EMU26722

Fuel level-alert indicator

If the fuel level decreases to one segment, the
fuel level alert segment will blink.
Do not continue to operate the engine with
full throttle if an alert device has activated.
Get back to the port within trolling engine
speed.

NOTICE:

Running out of fuel can

damage the engine.

[ECM01771]

EMU26733

Low battery voltage-alert indicator

If battery voltage drops, the display will auto-
matically turn on and blink.

Get back to the port soon if an alert device
has activated. For charging the battery, con-
sult your Yamaha dealer.

EMU26742

Fuel management meter

The fuel management meter shows the state
of the fuel consumption while the engine is
running.

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

EMU26753

Fuel flow meter

The fuel flow meter displays the amount of
fuel flow over a one-hour period, at the cur-
rent rate of engine operation.

1. Fuel level-alert segment

1. Low battery indicator

1. Fuel flow meter
2. Fuel consumption meter / Fuel economy

meter / Twin engine speed synchronizer

3. Water separator-alert indicator (operates

only if the sensor has been installed)

ZMU01748

U6P27AE0.book Page 27 Friday, December 6, 2013 6:17 PM

Содержание FL200C





































































































Результаты поиска

Содержание FL200C

Отзывы:

Yamaha FL200C, Руководство пользователя, Страница: 33 / 100

Результаты поиска

Содержание FL200C

Отзывы: