manualshive.com logo in svg

Yamaha FL200C, Руководство пользователя, Страница: 23 / 100

Поделиться
Скачать
Yamaha FL200C Скачать руководство пользователя страница 23

Components

17

EMU26191

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the lever
back from neutral engages reverse. The en-
gine will continue to run at idle until the lever
is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26234

Free accelerator

To open the throttle without shifting into ei-
ther forward or reverse, push the free accel-
erator button and move the remote control
lever.

TIP:

The free accelerator button can only be
pushed when the remote control lever is in
the neutral position.

After the button is pushed, the throttle be-
gins to open after the remote control lever
is moved at least 35°.

After using the free accelerator, return the
remote control lever to the neutral position.
The free accelerator button will return auto-

1. Remote control lever
2. Power trim and tilt switch
3. Free accelerator
4. Throttle friction adjuster

1. Neutral “ ”
2. Forward “ ”
3. Reverse “ ”
4. Shift
5. Fully closed
6. Throttle
7. Fully open

2

3

2

1

4

ZMU04569

N

1

F

7

6

2

R

3

4

4

6

5

7

5

ZMU04573

1. Fully open
2. Fully closed
3. Free accelerator

1. Fully open
2. Fully closed
3. Free accelerator

N

ZMU04576

1

3

2

1

3

2

ZMU04575

U6P27AE0.book  Page 17  Friday, December 6, 2013  6:17 PM

Содержание FL200C





































































































Отзывы:

Нет отзывов