Yamaha FL200C страница 97 Скачать руководство пользователя

Страница: 97 / 100

INDEX

Gasoline............................................ 2, 13
Gasoline exposure and spills.................. 2
Gear oil, changing................................. 75
Greasing ............................................... 65

Hot parts................................................. 1
Hour meter............................................ 24

Identification numbers record................. 4
Idle speed, inspecting .......................... 68
Impact damage..................................... 85
Installation requirements ...................... 10

Key number ............................................ 4

Laws and regulations.............................. 3
Low battery voltage-alert...................... 33
Low battery voltage-alert indicator....... 27
Low oil pressure alert ........................... 36
Low oil pressure-alert ........................... 31
Low oil pressure-alert indicator ............ 25
Lubrication............................................ 59

Main switch .......................................... 19
Maintenance chart 1............................. 62
Maintenance chart 2............................. 64
Modifications .......................................... 2
Mounting height.................................... 38
Mounting outboard motor .................... 11
Mounting the outboard motor .............. 38

Operating engine .................................. 46
Outboard motor disposal

requirements ...................................... 14

Outboard motor (painted surface),

checking ............................................. 60

Outboard motor safety ........................... 1

Outboard motor serial number ............... 4
Overheat alert ................................. 32, 36
Overheat-alert indicator ........................ 25
Overloading ............................................ 2

Passenger training .................................. 3
Passengers ............................................. 2
People in the water ................................. 2
Periodic maintenance ........................... 61
Personal flotation devices (PFDs) ........... 2
Power trim and tilt .................................. 1
Power trim and tilt switch (bottom

cowling) .............................................. 19

Power trim and tilt switch (remote

control) ............................................... 19

Power trim and tilt switches (twin

binnacle type) ..................................... 20

Power trim and tilt system, checking ... 44
Power trim and tilt will not operate ....... 87
Propeller ................................................. 1
Propeller, checking ............................... 73
Propeller (counter rotation models) ...... 12
Propeller, installing ............................... 74
Propeller, removing............................... 73
Propeller selection ................................ 11

Read manuals and labels ....................... 6
Remote control box .............................. 16
Remote control lever ............................ 17
Remote control requirements ............... 11
Replacement parts ............................... 61
Rotating parts ......................................... 1

Sending fuel.......................................... 46
Severe operating conditions................. 61
Shallow water ....................................... 55
Shifting.................................................. 49
Shifting (checks after engine warm

up)....................................................... 49

Spark plug, cleaning and adjusting ...... 67
Specifications ......................................... 9

U6P27AE0.book Page 91 Friday, December 6, 2013 6:17 PM

Содержание FL200C





































































































Результаты поиска

Содержание FL200C

Отзывы:

Похожие инструкции для FL200C

Бренды по названию

Популярные бренды

Yamaha FL200C, Руководство пользователя

Результаты поиска

Содержание FL200C

Отзывы:

Похожие инструкции для FL200C

Бренды по названию

Популярные бренды