Yamaha FL200C страница 94 Скачать руководство пользователя

Страница: 94 / 100

Trouble Recovery

Disconnect the water detection switch
coupler.

NOTICE:

Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-
tion could occur.

[ECM01951]

Unscrew the filter cup from the filter
housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when unscrewing the filter cup.

[ECM01961]

Drain the water in the filter cup by soak-
ing it up with a rag.

Firmly screw the filter cup onto the filter
housing.

NOTICE:

Be careful not to

twist the water detection switch lead
when screwing the filter cup onto the
filter housing.

[ECM01971]

Connect the water detection switch cou-
pler securely until a click is heard.

Fasten the water detection switch lead
with the holder.

1. Holder

1. Water detection switch coupler

1. Filter cup
2. Water detection switch lead

1. Water detection switch coupler

ZMU07550

U6P27AE0.book Page 88 Friday, December 6, 2013 6:17 PM

Содержание FL200C





































































































Результаты поиска

Содержание FL200C

Отзывы:

Похожие инструкции для FL200C

Бренды по названию

Популярные бренды

Yamaha FL200C, Руководство пользователя

Результаты поиска

Содержание FL200C

Отзывы:

Похожие инструкции для FL200C

Бренды по названию

Популярные бренды