Yamaha FL200C страница 88 Скачать руководство пользователя | Manualshive

Страница: 88 / 100

background image

Trouble Recovery

82

EMU29428

Troubleshooting

A problem in the fuel, compression, or igni-
tion systems can cause poor starting, loss of
power, or other problems. This section de-
scribes basic checks and possible remedies,
and covers all Yamaha outboard motors.
Therefore some items may not apply to your
model.
If your outboard motor requires repair, bring
it to your Yamaha dealer.
If the engine trouble-alert indicator is flashing,
consult your Yamaha dealer.

Starter will not operate.

Q. Is battery capacity weak or low?
A. Check battery condition. Use battery of
recommended capacity.

Q. Are battery connections loose or corrod-
ed?
A. Tighten battery cables and clean battery
terminals.

Q. Is fuse for electric start relay or electric cir-
cuit blown?
A. Check for cause of electric overload and
repair. Replace fuse with one of correct am-
perage.

Q. Are starter components faulty?
A. Have serviced by a Yamaha dealer.

Q. Is shift lever in gear?
A. Shift to neutral.

Engine will not start (starter operates).

Q. Is fuel tank empty?
A. Fill tank with clean, fresh fuel.

Q. Is fuel contaminated or stale?

A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged?
A. Clean or replace filter.

Q. Is starting procedure incorrect?
A. See page 46.

Q. Has fuel pump malfunctioned?
A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace
with recommended type.

Q. Are spark plug cap(s) fitted incorrectly?
A. Check and re-fit cap(s).

Q. Is ignition wiring damaged or poorly con-
nected?
A. Check wires for wear or breaks. Tighten all
loose connections. Replace worn or broken
wires.

Q. Are ignition parts faulty?
A. Have serviced by a Yamaha dealer.

Q. Is engine shut-off cord (lanyard) not at-
tached?
A. Attach cord.

Q. Are engine inner parts damaged?
A. Have serviced by a Yamaha dealer.

Engine idles irregularly or stalls.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace
with recommended type.

U6P27AE0.book Page 82 Friday, December 6, 2013 6:17 PM

«
...
86
87
88
89
90
...
»

Содержание FL200C





































































































Отзывы:

Нет отзывов

Похожие инструкции для FL200C

Бренд: Abit Страницы: 104

Бренд: AOpen Страницы: 156

Бренд: Elitegroup Computer Systems Страницы: 82

Бренд: CompuLab Страницы: 31

CLICKER 4 for STM32

Бренд: Mikroe Страницы: 16

Бренд: Supermicro Страницы: 142

Бренд: Gigabyte Страницы: 96

Бренд: Ublox Страницы: 42

K8T8AS - REV 3.0

Бренд: JETWAY Страницы: 26

Бренд: Humandata Страницы: 8

Бренд: ASROCK Страницы: 144

Бренд: MSI Страницы: 73

Бренд: Advantech Страницы: 88

Бренд: DFI Страницы: 150

TPS5420EVM-175 SWIFT

Бренд: Texas Instruments Страницы: 16

Бренд: Texas Instruments Страницы: 24

Бренд: Wolfson Страницы: 12

Бренд: AOpen Страницы: 125

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды