Yamaha FL200C страница 49 Скачать руководство пользователя

Страница: 49 / 100

Operation

garden hose connector is not properly
connected, cooling water can leak out and
the engine can overheat during operation.

[ECM01802]

EMU36942

Install cowling

Be sure that all cowling lock levers are
released.

Be sure that the rubber seal is seated all
the way around the engine.

Place the cowling on top of the seal.

Check to be sure it fits properly in the
rubber seal.

Move the levers to lock the cowling as
shown.

NOTICE:

If the top cowling is

not installed correctly, water spray
under the top cowling can damage the
engine, or the top cowling can blow
off at high speeds.

[ECM01992]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

1. Fitting
2. Flushing device

ZMU06164

ZMU06131

ZMU06133

U6P27AE0.book Page 43 Friday, December 6, 2013 6:17 PM

Содержание FL200C





































































































Результаты поиска

Содержание FL200C

Отзывы:

Похожие инструкции для FL200C

Бренды по названию

Популярные бренды

Yamaha FL200C, Руководство пользователя

Результаты поиска

Содержание FL200C

Отзывы:

Похожие инструкции для FL200C

Бренды по названию

Популярные бренды