Yamaha FL200C страница 4 Скачать руководство пользователя

Страница: 4 / 100

Table of contents

Safety information............................. 1

Outboard motor safety.................... 1

Boating safety ................................. 2

General information .......................... 4

Identification numbers record ......... 4

Outboard motor serial number........... 4
Key number ........................................ 4

EC Declaration of Conformity

(DoC) ........................................... 4

CE Marking .................................... 4
Read manuals and labels................ 6

Warning labels ................................... 6

Specifications and requirements..... 9

Specifications.................................. 9
Installation requirements............... 10

Boat horsepower rating.................... 10
Mounting outboard motor ................ 11

Remote control requirements ....... 11
Battery requirements..................... 11

Battery specifications....................... 11
Mounting battery .............................. 11

Multiple batteries.............................. 11

Propeller selection ........................ 11

Counter rotation models .................. 12

Start-in-gear protection ................  12
Engine oil requirements ................  12
Fuel requirements .........................  13

Gasoline ........................................... 13

Anti-fouling paint .......................... 13
Outboard motor disposal

requirements.............................. 14

Emergency equipment.................. 14

Components .................................... 15

Components diagram ................... 15

Remote control box..........................  16
Remote control lever ........................  17
Free accelerator ...............................  17
Throttle friction adjuster ...................  18
Engine shut-off cord (lanyard) and

clip ................................................ 18

Main switch ...................................... 19
Power trim and tilt switch on remote

control ........................................... 19

Power trim and tilt switch on bottom

cowling.......................................... 19

Power trim and tilt switches (twin

binnacle type)................................ 20

Trim tab with anode ......................... 20
Tilt support lever for power trim and

tilt model ....................................... 21

Cowling lock lever (pull up type) ......  21
Flushing device ................................  22
Fuel filter/Water separator................  22

Instruments and indicators ............ 24

Digital tachometer......................... 24

Tachometer ......................................  24
Trim meter ........................................  24
Hour meter .......................................  24
Low oil pressure-alert indicator........  25
Overheat-alert indicator ...................  25

Digital speedometer...................... 25

Speedometer.................................... 25

U6P27AE0.book Page 1 Friday, December 6, 2013 6:17 PM

Содержание FL200C





































































































Результаты поиска

Содержание FL200C

Отзывы:

Похожие инструкции для FL200C

Бренды по названию

Популярные бренды

Yamaha FL200C, Руководство пользователя

Результаты поиска

Содержание FL200C

Отзывы:

Похожие инструкции для FL200C

Бренды по названию

Популярные бренды