Yamaha FL150A Скачать руководство пользователя | Manualshive

Страница: 40 / 90

background image

Instruments and indicators

34

NOTICE

ECM00920

In such an event, the engine will not oper-
ate properly. Consult a Yamaha dealer im-
mediately.

EMU36170

Low battery voltage-alert

If the battery voltage drops, the low battery
voltage-alert indicator and the battery voltage
value will start to blink. Get back to the port
soon if the low battery voltage-alert device
has activated. For charging the battery, con-
sult your Yamaha dealer.

EMU36232

6Y8 Multifunction speed & fuel

meters

The speed & fuel meter unit shows the boat
speed and has the functions of fuel meter, to-
tal fuel consumption display, fuel economy
display, fuel flow display, and system voltage
display. The chosen display is selected by us-
ing the “

” (set) and “

” (mode) buttons

as described in this section. If the speed sen-
sor is installed, the unit can also show the trip
display. However, even if the speed sensor is
not installed, the trip display can be shown by
connecting an optional sensor to the unit. In
addition, if optional sensors are connected to
the unit, water surface temperature display,
depth display, and clock will also be available.
For the optional sensors, consult your
Yamaha dealer.

ZMU05425

ZMU05426

ZMU05427

ZMU05428

U63P7AE0.book Page 34 Thursday, February 25, 2010 1:14 PM

«
...
38
39
40
41
42
...
»

Содержание FL150A



























































































Отзывы:

Нет отзывов

Похожие инструкции для FL150A

Бренд: Yamaha Страницы: 82

Бренд: NXP Semiconductors Страницы: 6

Бренд: DFI Страницы: 104

Бренд: Biostar Страницы: 54

Бренд: DIEBOLD NIXDORF Страницы: 96

Бренд: TYAN Страницы: 63

Бренд: JETWAY Страницы: 44

Бренд: Magic-Pro Computer Страницы: 40

Бренд: Texas Instruments Страницы: 36

Бренд: ASROCK Страницы: 293

Бренд: EPC Страницы: 6

Бренд: Norco Страницы: 60

Бренд: Icop Страницы: 30

Бренд: Texas Instruments Страницы: 31

IRIS-W10 Series

Бренд: Ublox Страницы: 43

Бренд: California Instruments Страницы: 85

Бренд: Ublox Страницы: 23

Бренд: Portwell Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды