Yamaha FL150A страница 39 Скачать руководство пользователя | Manualshive

Страница: 39 / 90

background image

Instruments and indicators

33

EMU36221

Overheat alert

If the engine temperature rises too high while
cruising, the overheat-alert indicator will start
to blink. The engine speed will automatically
decrease to about 2000 r/min.

Stop the engine immediately if the buzzer
sounds and the overheat alert device has ac-
tivated. Check the cooling water inlet for clog-
ging.

NOTICE

ECM01592

●

Do not continue to run the engine if the
overheat-alert indicator blinks. Serious
engine damage will occur.

●

Do not continue to operate the engine if
a alert device has activated. Consult
your Yamaha dealer if the problem can-
not be located and corrected.

EMU36150

Water separator alert

This indicator will blink if water has accumulat-
ed in the water separator (fuel filter) while
cruising. In such an event, stop the engine im-
mediately and see page 80 of this manual to
drain the water from the fuel filter. Get back to
the port soon and consult a Yamaha dealer
immediately.

NOTICE

ECM00910

Gasoline mixed with water could cause
damage to the engine.

EMU36160

Engine trouble alert

This indicator will blink if the engine malfunc-
tions while cruising. Get back to the port soon
and consult a Yamaha dealer immediately.

ZMU05421

ZMU05422

ZMU05423

ZMU05424

U63P7AE0.book Page 33 Thursday, February 25, 2010 1:14 PM

«
...
37
38
39
40
41
...
»

Содержание FL150A



























































































Отзывы:

Нет отзывов

Похожие инструкции для FL150A

Industrial NUC-J6412

Бренд: ASROCK Страницы: 2

Бренд: MINN KOTA Страницы: 14

Бренд: Gigabyte Страницы: 96

Бренд: P&E Microcomputer Systems Страницы: 38

Бренд: Atmel Страницы: 16

DUOX Programmer

Бренд: Fermax Страницы: 99

H470 AORUS PRO AX

Бренд: Gigabyte Страницы: 52

Бренд: JETWAY Страницы: 57

THUNDER I7501 XTREME

Бренд: TYAN Страницы: 48

Бренд: DFI Страницы: 92

Бренд: NXP Semiconductors Страницы: 19

Бренд: ASROCK Страницы: 35

Бренд: DFI Страницы: 48

Бренд: MiTAC Страницы: 84

Бренд: ASROCK Страницы: 199

Бренд: DFI-ITOX Страницы: 112

Бренд: DFI-ITOX Страницы: 118

Бренд: California Instruments Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды