Yamaha FJR1300S(C) Скачать руководство пользователя страница 28

Страница: 28 / 99

INSTRUMENT AND CONTROL FUNCTIONS

3-11

EAU13430

Catalytic converter

This model is equipped with a catalytic
converter in the exhaust chamber.

WARNING

EWA10860

The exhaust system is hot after op-
eration. Make sure that the exhaust
system has cooled down before do-
ing any maintenance work.

CAUTION:

ECA10700

The following precautions must be
observed to prevent a fire hazard or
other damages.

●

Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.

●

Never park the vehicle near pos-
sible fire hazards such as grass
or other materials that easily
burn.

●

Do not allow the engine to idle
too long.

EAU14080

Seats

Rider seat

To remove the rider seat

1. Insert the key into the seat lock,

and then turn it as shown.

2. Pull the rider seat off.

To install the rider seat

1. Insert the projection on the front of

the rider seat into the seat holder
as shown, and then push the rear
of the seat down to lock it in place.

2. Remove the key.

Passenger seat

To remove the passenger seat

1. Remove the rider seat.
2. Pull the passenger seat up.

To install the passenger seat

1. Slide the receptacle on the rear of

the passenger seat over the seat
holder as shown, and then push
the front of the seat down.

1. Rider seat lock

2. Unlock.

1. Projection
2. Seat holder

5JW11.book Page 11 Friday, May 9, 2003 4:03 PM

Содержание FJR1300S(C)




































































































Результаты поиска

Содержание FJR1300S(C)

Отзывы:

Похожие инструкции для FJR1300S(C)

Бренды по названию

Популярные бренды

Yamaha FJR1300S(C), Руководство пользователя

Результаты поиска

Содержание FJR1300S(C)

Отзывы:

Похожие инструкции для FJR1300S(C)

Бренды по названию

Популярные бренды