Yamaha FJR1300S(C) Скачать руководство пользователя страница 74

Страница: 74 / 99

PERIODIC MAINTENANCE AND MINOR REPAIR

6-32

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

1. Headlight fuse
2. Signaling system fuse

3. Ignition fuse

4. Windshield motor fuse
5. Radiator fan fuse

6. Odometer and clock fuse (backup)

7. Spare fuse
8. Hazard fuse

9. ABS control unit fuse

10.Tail/position light fuse

1. Main fuse

Specified fuses:

Main fuse:

50.0 A

Headlight fuse:

25.0 A

Signaling system fuse:

15.0 A

Ignition fuse:

10.0 A

Windshield motor fuse:

2.0 A

Radiator fan fuse:

15.0 A

Hazard fuse:

7.5 A

Electronic fuel injection fuse:

15.0 A

ABS contorol unit fuse:

FJR1300A 7.5 A (CAL)(U49)

ABS motor fuse:

FJR1300A 30.0 A (CAL)(U49)

Odometer and clock fuse (backup):

10.0 A

Tail/position light fuse:

10.0 A

5JW11.book Page 32 Friday, May 9, 2003 4:03 PM

Содержание FJR1300S(C)




































































































Результаты поиска

Содержание FJR1300S(C)

Отзывы:

Похожие инструкции для FJR1300S(C)

Бренды по названию

Популярные бренды

Yamaha FJR1300S(C), Руководство пользователя

Результаты поиска

Содержание FJR1300S(C)

Отзывы:

Похожие инструкции для FJR1300S(C)

Бренды по названию

Популярные бренды