Yamaha FAZER FZ6-SV 2006 Скачать руководство пользователя страница 72

Страница: 72 / 90

PERIODIC MAINTENANCE AND MINOR REPAIR

6-32

EAU32830

Replacing an auxiliary light
bulb

This model is equipped with two auxil-
iary lights. If an auxiliary light bulb burns
out, replace it as follows.

1. Remove panel B (if replacing the

left auxiliary light bulb) or panel A
(if replacing the right auxiliary light
bulb). (See page 6-5.)

2. Remove the auxiliary light socket

(together with the coupler) by pull-
ing it out.

3. Remove the defective bulb by pull-

ing it out.

4. Insert a new bulb into the socket.

5. Install the auxiliary light socket (to-

gether with the coupler) by push-
ing it in.

EAU24360

Front wheel

EAU24470

To remove the front wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Place the motorcycle on the cen-

terstand.

2. Loosen the front wheel axle pinch

bolt, then the wheel axle and the
brake caliper bolts.

1. Auxiliary light bulb

2. Auxiliary light bulb socket

1. Wheel axle

2. Front wheel axle pinch bolt

U5VX22E0.book Page 32 Wednesday, September 14, 2005 11:42 AM

ProCarManuals.com

Содержание FAZER FZ6-SV 2006



























































































Результаты поиска

Содержание FAZER FZ6-SV 2006

Отзывы:

Похожие инструкции для FAZER FZ6-SV 2006

Бренды по названию

Популярные бренды

Yamaha FAZER FZ6-SV 2006, Руководство пользователя

Результаты поиска

Содержание FAZER FZ6-SV 2006

Отзывы:

Похожие инструкции для FAZER FZ6-SV 2006

Бренды по названию

Популярные бренды