manualshive.com logo in svg

Yamaha F9.9, Руководство пользователя

Поделиться
Скачать
Yamaha F9.9 Скачать руководство пользователя страница 38

Components

32

EMU26103

Power tilt switch

The power tilt system adjusts the outboard
motor angle in relation to the transom. Push-
ing the switch “

” (up) tilts the outboard mo-

tor up. Pressing the switch “

” (down) tilts

the outboard motor down. When the switch is
released, the outboard motor will stop in its
current position.

TIP:

For instructions on using the power tilt
switch, see pages 60 and 62.

EMU31433

Steering friction adjuster

A friction device provides adjustable resis-
tance to the steering mechanism, and can be
set according to operator preference. An ad-
juster lever is located on the bottom of the til-
ler handle bracket.
To increase resistance, turn the lever to the
port side “A”.
To decrease resistance, turn the lever to the
starboard side “B”.

WARNING

EWM00041

Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to steer, which could result in an
accident.

ON

START

OFF

ZMU01718

DN

UP

ZMU01720

U6DR38E0.book  Page 32  Tuesday, November 27, 2018  2:08 PM

©2020 

Yamaha 

Motor 

Corporation

Содержание F9.9

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды