Yamaha F9.9 Скачать руководство пользователя

Страница: 28 / 112

Specifications and requirements

NOTICE

ECM02421

Painted sacrificial anodes will not provide
corrosion protection.

EMU40302

Outboard motor disposal re-

quirements

Never illegally discard (dump) the outboard
motor. Yamaha recommends consulting the
dealer about discarding the outboard motor.

EMU36353

Emergency equipment

Keep the following items onboard in case
there is trouble with the outboard motor.



A tool kit with assorted screwdrivers, pliers,
wrenches (including metric sizes), and
electrical tape.



Waterproof flashlight with extra batteries.



An extra engine shut-off cord (lanyard) with
clip.



Spare parts, such as an extra set of spark
plugs.

Consult your Yamaha dealer for details.

EMU25223

Emission control information

EMU25232

This engine conforms to U.S. Environmental
Protection Agency (EPA) regulations for ma-
rine SI engines. See the label affixed to your
engine for details.

EMU25245

Approval label of emission control certifi-
cate

This label is attached at the location shown.
New Technology; (4-stroke/HPDI) EM

EMU25275

Star labels

Your outboard motor is labeled with a Califor-
nia Air Resources Board (CARB) star label.
See below for a description of your particular
label.

1. Approval label location

1. Star label location

ZMU07795

ISS

N C

TRO

L IN

FOR

MATIO

IS E

INE

NFO

RMS

ALIFORNIA

EXHAUST AND U.S. EPA E

XHAU

ST A

EVA

P R

R S

I M

INE

GIN

ES. R

EFER

TO OW

NER’S MAN

UAL FOR MAINTENANCE

SPEC

IFICA

TIO

D A

MIL

X PO

WER:

kW DIS

PLACEMENT: liters EPA

/CA F

EL:

+ N

, C

-h

R C

O.,L

TD.

ZMU07797

U6DR38E0.book Page 22 Tuesday, November 27, 2018 2:08 PM

Yamaha

Motor

Corporation

Содержание F9.9

















































































































Результаты поиска

Содержание F9.9

Отзывы:

Похожие инструкции для F9.9

Бренды по названию

Популярные бренды

Yamaha F9.9, Руководство пользователя

Результаты поиска

Содержание F9.9

Отзывы:

Похожие инструкции для F9.9

Бренды по названию

Популярные бренды