manualshive.com logo in svg

Yamaha F9.9, Руководство пользователя

Поделиться
Скачать
Yamaha F9.9 Скачать руководство пользователя страница 103

Trouble Recovery

97

6.

Insert the knotted end of the emergency
starter rope into the notch in the flywheel
rotor and wind the rope several turns
around the flywheel clockwise.

7.

Give a strong pull straight out to crank
and start the engine. Repeat if neces-
sary.

EMU29672

Engine fails to operate

EMU35322

Emergency engine operation

If the battery voltage is low or in the unlikely
event of an ignition system malfunction, the
engine speed may become erratic or the en-
gine may stop. In such a situation, follow the
procedure below.
Disconnect the yellow cord (emergency cir-
cuit) of the CDI unit.
Run the engine at low speed and return to
port. 

NOTICE:

 Follow this procedure only

in an emergency and just long enough to
return to port for repairs.

 [ECM00382]

EMU33502

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately. 

NOTICE:

 Do not attempt to run the

outboard motor until it has been com-
pletely inspected.

 [ECM00402]

ZMU07907

1. Yellow cord

U6DR38E0.book  Page 97  Tuesday, November 27, 2018  2:08 PM

©2020 

Yamaha 

Motor 

Corporation

Содержание F9.9

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды