Yamaha F75B Скачать руководство пользователя | Manualshive

Страница: 23 / 88

background image

Components

17

EMU25841

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

EMU25850

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

EMU25860

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

EMU26181

Remote control box

The remote control lever actuates both the
shifter and the throttle. The electrical switches
are mounted on the remote control box.

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the lever
back from neutral engages reverse. The en-
gine will continue to run at idle until the lever

is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into either
forward or reverse, put the remote control le-
ver in the neutral position and lift the neutral
throttle lever.

1. Power trim and tilt switch
2. Remote control lever

3. Neutral interlock trigger

4. Neutral throttle lever
5. Main switch / choke switch

6. Engine shut-off switch

7. Throttle friction adjuster

1. Neutral “ ”
2. Forward “ ”

3. Reverse “ ”

4. Shift
5. Fully closed

6. Throttle

7. Fully open

1. Neutral interlock trigger

U6D625E0.book Page 17 Thursday, March 13, 2008 9:06 AM

«
...
21
22
23
24
25
...
»

Содержание F75B

























































































Отзывы:

Нет отзывов

Похожие инструкции для F75B

Бренд: hager Страницы: 4

Cyclone IV GX FPGA

Бренд: Altera Страницы: 60

Бренд: Telit Wireless Solutions Страницы: 5

Бренд: J&W Страницы: 28

Бренд: Waveshare Страницы: 72

Бренд: NXP Semiconductors Страницы: 32

Бренд: Ublox Страницы: 22

Бренд: ST Страницы: 11

EVAL-AD2428WD1BZ

Бренд: Analog Devices Страницы: 6

Бренд: ST Страницы: 14

CC85-CC2590EM Series

Бренд: Texas Instruments Страницы: 7

Бренд: TRIGEM Страницы: 17

Бренд: DFI Страницы: 78

Бренд: DFI Страницы: 132

Бренд: DFI Страницы: 79

Force Trolling Motor 50"

Бренд: Garmin Страницы: 76

LANParty UT ICFX3200-T2/G

Бренд: DFI Страницы: 183

Бренд: DFI Страницы: 183

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды