Yamaha F400A Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 106

background image

Trouble Recovery

92

TIP:

When maneuvering at low speed, such as
near a dock, it is recommended to tilt the un-
used engine(s) down and to operate the un-
used engine(s) in neutral gear if possible.

EMU47621

Replacing fuse

EWM00632

Substituting an incorrect fuse or a piece of
wire could allow excessive current flow.
This could cause electric system damage
and a fire hazard.

The location of the fuse box for this model is
shown in the following illustration.

This model is equipped with the following
fuses.

TIP:



RC: Remote control

1. Fuse box

1

1. RC-ECU fuse (10 A)
2. Main switch / PTT switch fuse (20 A)
3. ETV fuse (10 A)
4. Fuel pump 2 fuse (15 A)
5. Fuel pump 1 fuse (15 A)
6. Fuel pump fuse (30 A)
7. Shift actuator fuse (15 A)
8. Starter relay fuse (30 A)
9. DI system 2 fuse (20 A)
10.DI system 1 fuse (20 A)
11.Engine ECU / Ignition coil fuse (30 A)
12.Fuel feed pump fuse (10 A)
13.Isolator 1 fuse (70 A)
14.Isolator 2 fuse (70 A)
15.Engine main 1 fuse (70 A)
16.Engine main 2 fuse (70 A)
17.Power STRG fuse (100 A)

1. Fuse box cover
2. Spare fuse (10 A, 15 A, 20 A, 30 A, 70 A, 100

A)

3. Fuse puller

17

16

15

14

13

1 2 3

4
5
6
7
8
9
10
11
12

1

3

2

2

2

2

2
2
2

U6KNK0E0.book Page 92 Monday, November 7, 2022 10:23 AM

«
...
96
97
98
99
100
...
»

Содержание F400A











































































































Отзывы:

Нет отзывов

Похожие инструкции для F400A

Бренд: Oakton Страницы: 4

Бренд: IET Labs Страницы: 114

Бренд: Hammond Organ Страницы: 25

Бренд: Hammond Organ Страницы: 87

Бренд: Make Noise Страницы: 15

Бренд: Major tech Страницы: 40

Бренд: Narvitech Страницы: 2

Бренд: National Instruments Страницы: 38

Бренд: ELGO Electronic Страницы: 24

OPERA CONTROL CENTER SERVER - V 3.5

Бренд: OPTICOM Страницы: 21

Бренд: Seben Страницы: 16

Бренд: Scaletron Страницы: 63

Panel Scope VPS10

Бренд: Velleman Страницы: 60

Multimar 25 EWR

Бренд: Mahr Страницы: 20

Бренд: Hanna Instruments Страницы: 2

Superstatic 749

Бренд: Sontex Страницы: 24

Бренд: Omega Страницы: 55

Бренд: LOVATO ELECTRIC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды