Yamaha F400A Скачать руководство пользователя страница 50

Страница: 50 / 106

Operation

EMU49240

Flushing device

Check that the garden hose connector cap
on the bottom cowling is securely installed.

NOTICE:

If the garden hose connector cap

is not properly installed, cooling water can
leak out and the engine can overheat dur-
ing operation.

[ECM05750]

EMU47570

Installing top cowling

(1) Check the rubber seal for damage. If the

rubber seal is damaged, have it replaced
by a Yamaha dealer.

(2) Check that the rubber seal is seated all

the way around the aprons.

(3) Check that all of the cowling lock levers

are pulled outward and turned upward.

(4) Place the top cowling on the aprons.

(5) Turn the cowling lock levers downward,

and then push them inward to secure the
top cowling.

1. Garden hose connector cap

1. Rubber seal
2. Apron

1. Top cowling

1. Cowling lock lever

U6KNK0E0.book Page 44 Monday, November 7, 2022 10:23 AM

Содержание F400A











































































































Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды

Yamaha F400A, Руководство пользователя

Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды