Yamaha F400A Скачать руководство пользователя страница 48

Страница: 48 / 106

Operation

EMU36443

Fuel system

EWM00061

Gasoline and its vapors are highly flamma-
ble and explosive. Keep away from sparks,
cigarettes, flames, or other sources of ig-
nition.

EWM00911

Leaking fuel can result in fire or explosion.



Check for fuel leakage regularly.



If any fuel leakage is found, the fuel sys-
tem must be repaired by a qualified me-
chanic. Improper repairs can make the
outboard unsafe to operate.

EMU36453

Check for fuel leaks



Check for fuel leaks or gasoline fumes in
the boat.



Check for fuel leakage from the fuel sys-
tem.



Check the fuel tank and fuel lines for
cracks, swellings, or other damage.

EMU37323

Checking the fuel filter

Check that the fuel filter is clean and free of
water. If any water is found in the fuel, or if a
significant amount of debris is found, the fuel
tank should be checked and cleaned by a
Yamaha dealer.

EMU47812

Controls

(1) Make sure that when the main switch is

turned “

” (on) or the “POWER” switch

is pressed, the DEC alert indicator will
come on in blue.

1. Fuel filter

1. DEC alert indicator

U6KNK0E0.book Page 42 Monday, November 7, 2022 10:23 AM

Содержание F400A











































































































Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды

Yamaha F400A, Руководство пользователя

Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды