Yamaha F30 Скачать руководство пользователя | Manualshive

Страница: 36 / 120

background image

Components

30

When constant speed is desired, tighten the
adjuster to maintain the desired throttle set-
ting.

EMU25996

Engine shut-off cord (lanyard) and
clip

The clip must be attached to the engine shut-
off switch for the engine to run. The cord
should be attached to a secure place on the
operator’s clothing, or arm or leg. Should the
operator fall overboard or leave the helm, the
cord will pull out the clip, stopping ignition to
the engine. This will prevent the boat from
running away under power.

WARNING! At-

tach the engine shut-off cord to a secure
place on your clothing, or your arm or leg
while operating. Do not attach the cord to
clothing that could tear loose. Do not
route the cord where it could become en-
tangled, preventing it from functioning.
Avoid accidentally pulling the cord dur-
ing normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power, the
boat could slow rapidly. This could cause
people and objects in the boat to be
thrown forward.

[EWM00123]

EMU26004

Engine stop button

The engine stop button stops the engine
when the button is pushed.

1. Engine shut-off cord (lanyard)
2. Clip
3. Engine shut-off switch

1. Engine shut-off cord (lanyard)
2. Clip
3. Engine shut-off switch

ZMU01716

1

2

3

6BG-9-3F-E0.book 30 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

Corporation

«
...
34
35
36
37
38
...
»

Содержание F30

























































































































Отзывы:

Нет отзывов

Похожие инструкции для F30

Бренд: Biostar Страницы: 54

Бренд: JETWAY Страницы: 54

GeForce 8300 (MI-A78U-8309)

Бренд: XFX Страницы: 26

Бренд: JETWAY Страницы: 52

STEVAL-ISB042V1

Бренд: ST Страницы: 26

Бренд: ISSC Страницы: 39

Бренд: Gigabyte Страницы: 40

SAM9N12/CN11-EK

Бренд: Atmel Страницы: 69

Бренд: Texas Instruments Страницы: 51

Бренд: TDK Страницы: 11

Бренд: JETWAY Страницы: 54

Бренд: Gigabyte Страницы: 96

Бренд: Advantech Страницы: 6

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 125

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды