Yamaha F25G Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 108

background image

Trouble Recovery

93

EMU29513

Power trim and tilt will not operate

If the engine cannot be tilted up or down with
the power trim and tilt because of a dis-
charged battery or a failure with the power
trim and tilt unit , the engine can be tilted
manually.
(1) Loosen the manual valve screw by turn-

ing it clockwise until it stops.

(2) Put the engine in the desired position,

then tighten the manual valve screw by
turning it counterclockwise.

EMU29534

Starter will not operate

If the starter mechanism does not operate
(the engine cannot be cranked with the start-
er), the engine can be started with an emer-
gency starter rope.

EWM01023



Use this procedure only in an emergen-
cy to return to the nearest port for re-
pairs.



When the emergency starter rope is
used to start the engine, the start-in-
gear protection device does not oper-
ate. Make sure the remote control lever
is in neutral. Otherwise the boat could
unexpectedly start to move, which
could result in an accident.



Attach the engine shut-off cord to a se-
cure place on your clothing, or your
arm or leg while operating the boat.



Do not attach the cord to clothing that
could tear loose. Do not route the cord
where it could become entangled, pre-
venting it from functioning.

1. Fuse puller
2. Cap
3. Fuse (20 A)
4. Spare fuse (20 A)

1. Fuse puller

2

3

4

1

ZMU08781

1

ZMU04337

1. Manual valve screw

1

ZMU08782

6FM-28199-75-1E0.book 93 ページ２０１９年１０月３０日　水曜日　午前１１時２３分

«
...
97
98
99
100
101
...
»

Содержание F25G













































































































Отзывы:

Нет отзывов

Похожие инструкции для F25G

Бренд: V2 ELETTRONICA Страницы: 12

Бренд: IEI Technology Страницы: 126

Бренд: National Semiconductor Страницы: 22

Бренд: Advantech Страницы: 4

Бренд: Biostar Страницы: 51

Бренд: IEI Technology Страницы: 156

Бренд: EPC Страницы: 10

Бренд: MSI Страницы: 126

Бренд: Analog Devices Страницы: 8

Бренд: Texas Instruments Страницы: 24

Бренд: Wolfson Страницы: 12

Бренд: Gigabyte Страницы: 96

Бренд: Yamaha Страницы: 82

Бренд: DFI Страницы: 155

M3A78-CM - Motherboard - Micro ATX

Бренд: Asus Страницы: 96

Бренд: Asus Страницы: 116

Бренд: Asus Страницы: 60

Бренд: Asus Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды