Yamaha F25G Скачать руководство пользователя страница 98

Страница: 98 / 108

Trouble Recovery

EMU29435

Temporary action in

emergency

EMU29442

Impact damage

EWM00871

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

(1) Stop the engine immediately.
(2) Check the control system and all compo-

nents for damage. Also, check the boat
for damage.

(3) Whether damage is found or not, return

to the nearest harbor slowly and careful-
ly.

(4) Have a Yamaha dealer check the out-

board motor before operating it again.

EMU30684

Replacing fuse

If a fuse has blown, open the fuse holder and
remove the fuse with a fuse puller. Replace
it with a spare one of the proper amperage.

EWM00632

Substituting an incorrect fuse or a piece
of wire could allow excessive current
flow. This could cause electric system
damage and a fire hazard.

Consult your Yamaha dealer if the new fuse
immediately blows again.

Have motor
adjusted to proper
transom height.

Is trim angle incorrect?

Adjust trim angle to achieve most effi-
cient operation.

Is motor mounted at incorrect height
on transom?

Have motor adjusted to proper tran-
som height.

Trouble

Engine vibrates excessively.

Item

Question

Answer

Propeller

Is propeller damaged?

Have propeller repaired or replaced.

Are weeds or other foreign material
tangled on propeller?

Remove and clean propeller.

Propeller shaft

Is propeller shaft damaged?

Have serviced by a Yamaha dealer.

Outboard motor
mounting

Are outboard motor mounting bolts
loose?

Tighten bolts or have serviced by a
Yamaha dealer.

Steering pivot

Is steering pivot loose or damaged?

Have serviced by a Yamaha dealer.

Trouble

Engine power loss.

Item

Question

Answer

6FM-28199-75-1E0.book 92 ページ２０１９年１０月３０日　水曜日　午前１１時２３分

Содержание F25G













































































































Результаты поиска

Содержание F25G

Отзывы:

Похожие инструкции для F25G

Бренды по названию

Популярные бренды

Yamaha F25G, Руководство пользователя

Результаты поиска

Содержание F25G

Отзывы:

Похожие инструкции для F25G

Бренды по названию

Популярные бренды