Yamaha F25G Скачать руководство пользователя страница 94

Страница: 94 / 108

Maintenance

should be clean, secure, and covered by
an insulating cover.

WARNING! Bad

connections can produce shorting or
arcing and cause an explosion.

[EWM01913]

EMU29335

Connecting the battery

EWM00573

Mount the battery holder securely in a
dry, well-ventilated, vibration-free loca-
tion in the boat. Install a fully charged bat-
tery in the holder.

ECM01125

Do not reverse the battery cables. Other-
wise, the electrical parts could be dam-
aged.

(1) Make sure the main switch (on applica-

ble models) is “

” (off) before working

on the battery.

(2) Connect the red battery cable to the

POSITIVE (+) terminal first. Then con-
nect the black battery cable to the NEG-
ATIVE (-) terminal.

(3) The electrical contacts of the battery and

cables must be clean and properly con-
nected, or the battery will not start the
engine.

EMU29372

Disconnecting the battery

(1) Turn off the battery cut-off switch (if

equipped) and main switch.

NOTICE:

they are left on, the electrical system
can be damaged.

[ECM01931]

(2) Disconnect the negative cable(s) from

the negative (-) terminal.

NOTICE:

Al-

ways disconnect all negative (-) ca-
bles first to avoid a short circuit and
damage to the electrical system.

[ECM01941]

(3) Disconnect the positive cable(s) and re-

move the battery from the boat.

(4) Clean, maintain, and store the battery

according to the manufacturer’s instruc-
tions.

1. Red cable
2. Black cable
3. Battery

6FM-28199-75-1E0.book 88 ページ２０１９年１０月３０日　水曜日　午前１１時２３分

Содержание F25G













































































































Результаты поиска

Содержание F25G

Отзывы:

Похожие инструкции для F25G

Бренды по названию

Популярные бренды

Yamaha F25G, Руководство пользователя

Результаты поиска

Содержание F25G

Отзывы:

Похожие инструкции для F25G

Бренды по названию

Популярные бренды