Yamaha F25G Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 108

background image

Maintenance

85

equipped), and thrust washer.

EMU30673

Installing propeller

EMU46121

Spline models

ECM00502

Make sure to use a new cotter pin and
bend the ends over securely. Otherwise,
the propeller could come off during oper-
ation and be lost.

(1) Apply Yamalube Marine Grease or a

corrosion resistant grease to the propel-
ler shaft.

(2) Install the spacer (if equipped), thrust

washer, washer (if equipped), and pro-
peller on the propeller shaft.

NOTICE:

Make sure to install the thrust washer
before installing the propeller. Other-
wise, the lower case and propeller
boss could be damaged.

[ECM01882]

(3) Install the spacer (if equipped) and the

washer. Tighten the propeller nut to the
specified torque.

(4) Align the propeller nut slot with the pro-

peller shaft hole. Insert a new cotter pin
in the hole and bend the cotter pin ends.

NOTICE:

Do not reuse the cotter pin.

Otherwise, the propeller can come off
during operation.

[ECM01892]

TIP:

If the propeller nut slot does not align with the
propeller shaft hole after tightening the pro-
peller nut to the specified torque, tighten the
nut further to align the slot with the hole.

EMU47070

Changing gear oil

EWM00801



Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.



Never get under the lower unit while it
is tilted, even when the tilt support lever
or knob is locked. Severe injury could
occur if the outboard motor accidental-
ly falls.

(1) Tilt the outboard motor so that the gear

oil drain screw is at the lowest point pos-
sible.

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

ZMU06564

6

5

4

3

2

1

Propeller nut tightening torque:

34 N·m (3.4 kgf·m, 25 lb·ft)

ZMU0206

3

6FM-28199-75-1E0.book 85 ページ２０１９年１０月３０日　水曜日　午前１１時２３分

«
...
89
90
91
92
93
...
»

Содержание F25G













































































































Отзывы:

Нет отзывов

Похожие инструкции для F25G

Бренд: BIGTREETECH Страницы: 39

Бренд: Supero Страницы: 90

Бренд: IEI Technology Страницы: 153

Бренд: Aaeon Страницы: 50

Бренд: BCM Страницы: 3

8A 72QFN Series

Бренд: IDT Страницы: 29

FRDMDUALK3664EVB

Бренд: NXP Semiconductors Страницы: 17

Бренд: Javad Страницы: 12

Бренд: DFI Страницы: 96

Бренд: Honda Страницы: 132

LPC1768-Xplorer

Бренд: NGX Technologies Страницы: 25

EVAL-AD2428WD1BZ

Бренд: Analog Devices Страницы: 6

Бренд: Aaeon Страницы: 74

H97M Anniversary

Бренд: ASROCK Страницы: 152

Бренд: unicore Страницы: 11

Бренд: Supermicro Страницы: 1

Бренд: Fujitsu Страницы: 27

Бренд: Fujitsu Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды