Yamaha F25G Скачать руководство пользователя страница 48

Страница: 48 / 108

Operation

board motor is not level, the oil level
indicated on the oil dipstick may not
be accurate.

[ECM01862]

(2) Remove the oil dipstick and wipe it

clean.

(3) Insert the oil dipstick completely and re-

move it again.

(4) Check that the oil level on the oil dipstick

is between the upper and lower marks.
Consult your Yamaha dealer if the oil
level is not at the proper level or if it ap-
pears milky or dirty.

EMU27154

Engine



Check the engine and engine mounting.



Look for loose or damaged fasteners.



Check the propeller for damage.



Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out
and the engine can overheat during oper-
ation.

[ECM01802]

EMU36956

Install top cowling

(1) Be sure that the cowling lock lever is re-

leased.

(2) Be sure that the rubber seal is seated all

the way around the top cowling.

1. Oil dipstick

1. Oil dipstick
2. Lower mark
3. Upper mark

ZMU0

751

ZMU08752

1. Fitting
2. Flushing device

ZMU08753

6FM-28199-75-1E0.book 42 ページ２０１９年１０月３０日　水曜日　午前１１時２３分

Содержание F25G













































































































Результаты поиска

Содержание F25G

Отзывы:

Похожие инструкции для F25G

Бренды по названию

Популярные бренды

Yamaha F25G, Руководство пользователя

Результаты поиска

Содержание F25G

Отзывы:

Похожие инструкции для F25G

Бренды по названию

Популярные бренды