Yamaha F20G страница 92 Скачать руководство пользователя

Страница: 92 / 108

Maintenance

(3) Remove the propeller, washer (if

equipped), and thrust washer.

EMU30673

Installing propeller

EMU46121

Spline models

ECM00502

Make sure to use a new cotter pin and
bend the ends over securely. Otherwise,
the propeller could come off during oper-
ation and be lost.

(1) Apply Yamalube Marine Grease or a

corrosion resistant grease to the propel-
ler shaft.

(2) Install the spacer (if equipped), thrust

washer, washer (if equipped), and pro-
peller on the propeller shaft.

NOTICE:

Make sure to install the thrust washer
before installing the propeller. Other-
wise, the lower case and propeller
boss could be damaged.

[ECM01882]

(3) Install the spacer (if equipped) and the

washer. Tighten the propeller nut to the

specified torque.

(4) Align the propeller nut slot with the pro-

peller shaft hole. Insert a new cotter pin
in the hole and bend the cotter pin ends.

NOTICE:

Do not reuse the cotter pin.

Otherwise, the propeller can come off
during operation.

[ECM01892]

TIP:

If the propeller nut slot does not align with the
propeller shaft hole after tightening the pro-
peller nut to the specified torque, tighten the

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

ZMU08156

4 3

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

Propeller nut tightening torque:

34 N·m (3.4 kgf·m, 25 lb·ft)

ZMU06564

ZMU0206

6HY-9-71-1E0.book 86 ページ２０１９年１２月４日　水曜日　午後２時５１分

Содержание F20G













































































































Результаты поиска

Содержание F20G

Отзывы:

Похожие инструкции для F20G

Бренды по названию

Популярные бренды

Yamaha F20G, Руководство пользователя

Результаты поиска

Содержание F20G

Отзывы:

Похожие инструкции для F20G

Бренды по названию

Популярные бренды