manualshive.com logo in svg

Yamaha F200D, Руководство пользователя

Поделиться
Скачать
Yamaha F200D Скачать руководство пользователя страница 31

Basic components

25

●

The buzzer will sound.

If the warning system has activated, stop the
engine and check the cooling water inlet for
clogging.

NOTE:

Dual engine drive users:
Should the overheat warning system of one
engine activate, the engine will slow down
and the buzzer will sound. This will cause the
other engine to slow down and the buzzer to
sound. To switch off the warning activation on
the engine not affected by overheating, turn
off the main switch of the engine overheating.

EMU26853

Low oil pressure warning

If the oil pressure drops too low, the warning
device will activate.
Activation of warning device

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

The low oil pressure warning indicator will
light.

●

The buzzer will sound.

If the warning system has activated, stop the
engine as soon as it is safe to do so. Check
the oil level and add oil as needed. If the oil
level is correct and the warning device does
not switch off, consult your Yamaha dealer.

OFF

START

ON

OFF

START

ON

ZMU04584

ZMU01828

OFF

START

ON

OFF

START

ON

ZMU04584

U69J14E0.book  Page 25  Friday, March 12, 2004  10:20 AM

Содержание F200D


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды