LOWR
Lower unit
8-31
TIP:
While turning the drive shaft clockwise, push
the water pump housing down to install it.
Checking the lower unit for air
leakage
1.
Remove the check screw
1
, and then
connect the special service tool
2
.
2.
Apply the specified pressure. Check that
the pressure is maintained in the lower
unit for 10 seconds or more.
NOTICE:
Do not over pressurize the lower unit.
Otherwise, the oil seals could be dam-
aged.
Installing the lower unit
• Make sure to disconnect the battery
cables from the battery, and remove the
clip from the engine shut-off switch.
• When installing the lower unit with the
power unit installed, make sure to sus-
pend the outboard motor. Otherwise, the
outboard motor could fall suddenly and
result in severe injuries.
• When loosening or tightening the pro-
peller nut, do not hold the propeller
using your hands.
1.
Align the pin
a
on the shift lever with the
alignment mark
b
on the bottom cowl-
ing.
2.
Set the gear shift to the N position.
3.
Install the dowels
2
.
4.
Install the extension
3
(U-transom
model) and lower unit
4
, and then
tighten the lower case mounting bolts
5
and lower case mounting nuts
6
(U-tran-
som model) to the specified torques.
NOTICE:
Make sure to align the
splines on the lower unit shift rod with
the splines on the upper case shift
rod. Otherwise, the shift rods could be
bent.
5.
Install the trim tab
7
to its original posi-
tion, and then tighten the trim tab bolt
8
to the specified torque.
Leakage tester
2
: 90890-06840
Holding pressure:
68.6 kPa (0.686 kgf/cm
2
, 9.9 psi)
1
2
Shift rod socket
1
: 90890-06679
a
b
1
R
N
F
Содержание F200B
