Yamaha F150G Скачать руководство пользователя страница 38

Страница: 38 / 104

Instruments and indicators

EMU41683

Overheat alert

If the engine temperature rises too high while
cruising, the pop-up window will appear.
Press the “

” (set) button to change to nor-

mal display, and the overheat-alert indicator
will start to blink. The engine speed will auto-
matically decrease to about 2000–3500
r/min.

Stop the engine immediately if the buzzer
sounds and the overheat alert device has ac-
tivated. Check the cooling water inlet for
clogging.

NOTICE

ECM01594



Do not continue to run the engine if the
overheat-alert indicator blinks. Serious
engine damage will occur.



Do not continue to operate the engine if
an alert device has activated. Consult
your Yamaha dealer if the problem can-
not be located and corrected.

EMU41692

Low oil pressure-alert

If the engine oil pressure drops too low, the
pop-up window will appear. Press the “

”

(set) button to change to normal display, and
the low oil pressure-alert indicator will start to
blink. The engine speed will automatically de-
crease to about 2000–3500 r/min.

ZMU07237

ZMU07238

ZMU07239

ZMU07240

ZMU07241

U6DV75E0.book Page 31 Tuesday, February 21, 2017 8:33 AM

Содержание F150G









































































































Результаты поиска

Содержание F150G

Отзывы:

Бренды по названию

Популярные бренды

Yamaha F150G, Руководство пользователя

Результаты поиска

Содержание F150G

Отзывы:

Бренды по названию

Популярные бренды