manualshive.com logo in svg

Yamaha F150A2, Руководство пользователя

Поделиться
Скачать
Yamaha F150A2 Скачать руководство пользователя страница 88

Maintenance

82

thrust washer before installing the
propeller. Otherwise, the lower case
and propeller boss could be damaged.

[ECM01882]

3.

Install the spacer, washer, and propeller
nut. Tighten the propeller nut to the
specified torque.

TIP:

Make sure to align the protrusions on the
spacer with the cutout areas of the propeller.
4.

Align the propeller nut slot with the pro-
peller shaft hole. Insert a new cotter pin
in the hole and bend the cotter pin ends.

NOTICE:

 Do not reuse the cotter pin.

Otherwise, the propeller can come off
during operation.

 [ECM01892]

TIP:

If the propeller nut slot does not align with the
propeller shaft hole after tightening the pro-
peller nut to the specified torque, tighten the
nut further to align the slot with the hole.

EMU2928C

Changing gear oil

WARNING

EWM00801

Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

Never get under the lower unit while it is
tilted, even when the tilt support lever or
knob is locked. Severe injury could oc-
cur if the outboard motor accidentally
falls.

1.

Tilt the outboard motor so that the gear
oil drain screw is at the lowest point pos-
sible.

2.

Place a suitable container under the gear
case.

3.

Remove the gear oil drain screw and
gasket. 

NOTICE:

 If there is an exces-

sive quantity of metal particles on the
magnetic gear oil drain screw, this
can indicate lower unit problem. Con-
sult your Yamaha dealer.

 [ECM01901]

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

Propeller nut tightening torque:

54 Nm (5.51 kgf-m, 39.8 ft-lb)

ZMU07844

4 3

2

1

5

6

1. Cotter pin

1

ZMU06956

U63P3FE0.book  Page 82  Thursday, December 5, 2013  10:01 AM

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F150A2













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды