background image

Maintenance

69

7.

Leave the outboard motor for 5-10 min-
utes.

8.

Remove oil dipstick and wipe it clean.

9.

Insert the dipstick and remove it again.
Be sure to completely insert the dipstick
into the dipstick guide, otherwise the oil
level measurement will be incorrect.

10. Recheck the oil level using the dipstick to

be sure the level falls between the upper
and lower marks. Consult your Yamaha
dealer if the oil level is out of specified lev-
el.

11. Start the engine and make sure that the

low oil pressure-alert indicator remains
off. Also, make sure that there are no oil
leaks. 

NOTICE:

 If the low oil pressure-

alert indicator comes on or if there are
oil leaks, stop the engine and find the
cause. Continued operation with a
problem could cause severe engine
damage. Consult your Yamaha dealer
if the problem cannot be located and
corrected.

 [ECM01622]

12. Dispose of used oil according to local

regulations.

TIP:

For more information on the disposal of
used oil, consult your Yamaha dealer.

Change the oil more often when operating
the engine under adverse conditions such
as extended trolling.

EMU29114

Inspecting wiring and connectors

Inspect that each connector is engaged se-
curely.

Inspect that each ground lead is properly
secured.

1. Oil filler cap

Recommended engine oil:

4-stroke outboard motor oil

Replacement engine oil quantity (at peri-
odic maintenance):

Without oil filter replacement:

4.3 L (4.55 US qt, 3.78 Imp.qt)

With oil filter replacement:

4.5 L (4.76 US qt, 3.96 Imp.qt)

1. Oil dipstick

2. Lower level mark

3. Upper level mark

1

3

2

ZMU07056

U63P2AE0.book  Page 69  Monday, March 1, 2010  1:49 PM

Содержание F150A



























































































Отзывы: