Yamaha DTX Drums DTX502, Руководство пользователя

Страница: 61 / 92

Advanced Techniques
DTX502 O w ner’s Man u al
Setting Parameters using Menu Mode
61
KitV12
Hold Mode
q
Trigger input source
See
q
Trigger input source from the description of the KitV1
page. The setting made on this page applies to both Layer A
and Layer B.
w
HoldMode
Use this parameter to turn Hold mode on or off for voices
produced by the specified trigger input source.
KitV13
Alternate Group
q
Trigger input source
See
q
Trigger input source from the description of the KitV1
page. The setting made on this page applies to both Layer A
and Layer B.
w
AltGrp
Use this parameter to assign the voices produced by the spec-
ified trigger input source to an alternate group—that is, a col-
lection of voices that you do not want to play simultaneously,
such as open and closed hi-hats. If a voice is triggered while
another from the same alternate group is already playing, the
earlier voice will be silenced before the new one is played.
The KitCommon area is used to set parameters that apply to the
current kit.
KitC1
Double Bass Switch
q
DblBass
By setting this parameter to “on”, you can easily configure
your drum module to produce a kick drum sound whenever
you operate the pedal connected to the [HI-HAT CONTROL]
trigger input jack. This convenient function provides support
for double bass drumming techniques.
KitC2
Reverb Send (Voices)
q
RevSendDr
Use this parameter to specify the level at which all of the cur-
rent kit’s drum voices are to be sent to the built-in reverb unit.
Settings Description
on
MIDI Note On and Note Off messages are
o
u tp u t alternately w hene v er the pad is str u ck.
Note that w hen Wa v e Voice (W) has b een
specified as the v oice category, the Wa v e
Voice w ill b e played repeatedly.
off
This setting corresponds to normal operation:
A MIDI Note On message is o
u tp u t w hen the
pad is str u ck, and the corresponding MIDI
Note Off message is o u tp u t a u tomatically after
the gate time has elapsed.
Settings Description
off Voice is not assigned to an alternate gro u p
HHOpen Open Hi-hat gro u p
HHClose Closed Hi-hat gro u p
1 to 9
N u m b ered alternate gro u ps: Voices that yo u
do not w ant to play sim u ltaneo u sly can b e
freely assigned to them.
NOTE
The Open Hi-hat gro u p and the Closed Hi-hat gro u p operate
according to the follo w ing r u les.
• When a v oice from the Open Hi-hat gro u p is triggered, other
v oices from that gro u p and those from the Closed Hi-hat
gro u p are not silenced.
• When a v oice from the Closed Hi-hat gro u p is triggered, all
v oices from the Open Hi-Hat gro u p are silenced.
>Ki t V12 snareHd
” HoldMode=off ‚
w
q
>Ki t V13 snareHd
” Al t Grp=off
w
q
03: KitCommon Area
Settings affecting entire kits
Settings off or on
NOTE
Opening and closing of the hi-hat is not possi b le w hen D b lBass
is set to “on”.
Settings
0 to 127
NOTE
The Re v SendDr parameter affects all of the c u rrent kit’s dr u m
v oices. To adj u st the re v er b le v el for indi v id u al pads or trigger
inp u t so u rces, u se the Re v er b Send (So u rce) parameter
(Re v Send) from the KitVoice area (page 60).
>Ki t C1
” DblBass=off ‚
q
>Ki t C2
” Re V SendDr= 60‚
q