background image

12 

En

Refer to the chart below should the unit not function properly. If the problem you are experiencing is not listed below, 
or if the instruction below does not help, set the unit to the standby mode, disconnect the AC power supply cable, and 
contact the nearest authorized Yamaha dealer or service center. Check the below first.
1 The AC power supply cable of the unit, TV and external components (such as BD player) are firmly connected to 

the AC wall outlet.

2 The power supply of the unit, TV and the external components (such as BD player) are turned on.
3 All cables are firmly connected to their respective jacks on each component.

Troubleshooting

Problem

Cause

Solution

See 

page

Power turns on but 
immediately shuts off.

The power cable may be connected improperly. Make sure the power cable is plugged into the 

outlet firmly.

4

The unit may have received a strong electrical 
shock, such as from a lightening bolt or 
excessive static electricity.

Set the unit to standby mode, and then 
disconnect the power cable. Wait for about 30 
seconds, connect the power cable, and then turn 
the unit on again.

The unit has an auto-sleep function, which will 
automatically set to standby mode if the unit is 
left turned on for 12 hours without any 
operation being performed.

The speakers make no 
sound.

The volume may be set to minimum.

Adjust the volume level.

8

The mute function may be activated.

Press MUTE on the remote control to cancel the 
mute function and adjust the volume.

8

The input source or input setting may be 
incorrect.

Select the correct input source or input setting.

7

Surround effect is not 
achieved.

A surround mode is not selected.

Press SURROUND on the remote control to 
play back the source in surround effect.

7

No bass / The external 
subwoofer makes no sound.

The volume of the subwoofer channel may be 
set to minimum level.

Adjust the volume level of the subwoofer.

8

Opposite setting of subwoofer is selected.

Select collect setting of subwoofer.

8

The source does not contain low frequency 
signals.

The cable between the unit and the subwoofer 
not connected when selecting playback of the 
external subwoofer.

Connect the unit and the external subwoofer by 
using a subwoofer pin cable.

5

The volume level decreases 
without any operation.

The unit controls its volume within a certain 
level to prevent the next playback from sudden 
output at excessive volume.

Reset the volume.

8

This unit does not operate 
properly.

The unit may receive a strong electrical shock, 
such as from a lightening bolt or excessive static 
electricity, or drop in power supply.

Set the unit to standby mode, and then 
disconnect the power cable. Wait for about 30 
seconds, connect the power cable, and then turn 
on the unit again.

A digital or high-frequency 
equipment produces noises.

The unit may be placed close to digital 
equipment or high-frequency equipment.

Place the unit away from such equipment.

The remote control does not 
operate the unit.

The unit may be outside the remote control 
operation range.

The operation range for the remote control of 
the unit is within 6 m (20 ft).

6

The remote control sensor of the unit may be 
exposed to direct sunlight or other lighting.

Change the lighting or reposition the unit.

The batteries may be worn out.

Replace the batteries.

6

The volume of the unit and TV 
increases simultaneously.

Your TV itself received the signal from TV 
remote control, having learned the operation of 
the unit.

Set the volume of your TV to minimum, or set 
the audio output of your TV built-in speaker to 
off.

Adjust the volume by using the remote control 
of the unit.

8

Содержание ATS-1010





















Отзывы: