Yamaha 9.9F Скачать руководство пользователя | Manualshive

Страница: 58 / 62

background image

Trouble Recovery

53

A. Connect correctly.

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29433

Temporary action in emergency

EMU29441

Impact damage

WARNING

EWM00870

The outboard motor can be seriously dam-
aged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

1.

Stop the engine immediately.

2.

Check the control system and all compo-
nents for damage. Also, check the boat
for damage.

3.

Whether damage is found or not, return
to the nearest harbor slowly and careful-
ly.

4.

Have a Yamaha dealer check the out-
board motor before operating it again.

EMU29533

Starter will not operate

If the starter mechanism does not operate
(the engine cannot be cranked with the start-
er), the engine can be started with an emer-
gency starter rope.

WARNING

EWM01022

●

Use this procedure only in an emergen-
cy to return to the nearest port for re-
pairs.

●

When the emergency starter rope is
used to start the engine, the start-in-
gear protection device does not operate.
Make sure the remote control lever is in
neutral. Otherwise the boat could unex-
pectedly start to move, which could re-
sult in an accident.

●

Attach the engine shut-off cord to a se-
cure place on your clothing, or your arm
or leg while operating the boat.

U63V2DE0.book Page 53 Monday, February 22, 2010 9:00 AM

«
...
56
57
58
59
60
...
»

Содержание 9.9F































































Отзывы:

Нет отзывов

Похожие инструкции для 9.9F

Бренд: Yamaha Страницы: 76

Бренд: CIRCUIT DESIGN Страницы: 9

Бренд: Xilinx Страницы: 40

Бренд: MSI Страницы: 30

Бренд: Gigabyte Страницы: 40

Бренд: EVGA Страницы: 14

Бренд: Atmel Страницы: 30

Бренд: Shuttle Страницы: 81

Бренд: EVGA Страницы: 2

NB7NPQ1102MCMUGEVB

Бренд: onsemi Страницы: 7

Бренд: National Semiconductor Страницы: 22

Бренд: Vox Technologies Страницы: 36

NB-IoT Module Series

Бренд: Quectel Страницы: 31

Бренд: Seanix Страницы: 49

Бренд: Gigabyte Страницы: 96

Бренд: Biostar Страницы: 68

Бренд: ASROCK Страницы: 4

Бренд: TYAN Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды