Yamaha 9.9F страница 55 Скачать руководство пользователя | Manualshive

Страница: 55 / 62

background image

Trouble Recovery

50

EMU29427

Troubleshooting

A problem in the fuel, compression, or ignition
systems can cause poor starting, loss of pow-
er, or other problems. This section describes
basic checks and possible remedies, and cov-
ers all Yamaha outboard motors. Therefore
some items may not apply to your model.
If your outboard motor requires repair, bring it
to your Yamaha dealer.
If the engine trouble-alert indicator is flashing,
consult your Yamaha dealer.

Starter will not operate.

Q. Is battery capacity weak or low?
A. Check battery condition. Use battery of rec-
ommended capacity.

Q. Are battery connections loose or corrod-
ed?
A. Tighten battery cables and clean battery
terminals.

Q. Is fuse for electric start relay or electric cir-
cuit blown?
A. Check for cause of electric overload and
repair. Replace fuse with one of correct am-
perage.

Q. Are starter components faulty?
A. Have serviced by a Yamaha dealer.

Q. Is shift lever in gear?
A. Shift to neutral.

Engine will not start (starter operates).

Q. Is fuel tank empty?
A. Fill tank with clean, fresh fuel.

Q. Is fuel contaminated or stale?
A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged?
A. Clean or replace filter.

Q. Is starting procedure incorrect?
A. See page 27.

Q. Has fuel pump malfunctioned?
A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace with
recommended type.

Q. Are spark plug cap(s) fitted incorrectly?
A. Check and re-fit cap(s).

Q. Is ignition wiring damaged or poorly con-
nected?
A. Check wires for wear or breaks. Tighten all
loose connections. Replace worn or broken
wires.

Q. Are ignition parts faulty?
A. Have serviced by a Yamaha dealer.

Q. Is engine shut-off cord (lanyard) not at-
tached?
A. Attach cord.

Q. Are engine inner parts damaged?
A. Have serviced by a Yamaha dealer.

Engine idles irregularly or stalls.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace with
recommended type.

Q. Is fuel system obstructed?

U63V2DE0.book Page 50 Monday, February 22, 2010 9:00 AM

«
...
53
54
55
56
57
...
»

Содержание 9.9F































































Отзывы:

Нет отзывов

Похожие инструкции для 9.9F

Бренд: QDI Страницы: 22

Бренд: ASROCK Страницы: 5

RTKA223012DR0050BU

Бренд: Renesas Страницы: 14

Бренд: Texas Instruments Страницы: 19

Бренд: MSI Страницы: 94

Бренд: Biostar Страницы: 63

Бренд: Renesas Страницы: 30

8A 72QFN Series

Бренд: IDT Страницы: 29

Бренд: Atiosys Страницы: 1

SAM9N12/CN11-EK

Бренд: Atmel Страницы: 69

Бренд: Albatron Страницы: 57

Бренд: Aaeon Страницы: 108

Бренд: MATSONIC Страницы: 39

MT9V113PACSTCH-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: OLIMEX Страницы: 14

Бренд: Nuvoton Страницы: 11

Бренд: Rohm Страницы: 8

Бренд: MiTAC Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды