Yamaha 9.9F Скачать руководство пользователя | Manualshive

Страница: 52 / 62

background image

Maintenance

47

TIP:

If the propeller nut does not align with the pro-
peller shaft hole after tightening to the speci-
fied torque, tighten the nut further to align it
with the hole.

EMU29289

Changing gear oil

WARNING

EWM00800

●

Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

●

Never get under the lower unit while it is
tilted, even when the tilt support lever or
knob is locked. Severe injury could oc-
cur if the outboard motor accidentally
falls.

1.

Tilt the outboard motor so that the gear oil
drain screw is at the lowest point possi-
ble.

2.

Place a suitable container under the gear
case.

3.

Remove the gear oil drain screw and gas-
ket.

NOTICE:

If there is an excessive

quantity of metal particles on the mag-
netic gear oil drain screw, this can in-
dicate lower unit problem. Consult
your Yamaha dealer.

[ECM01900]

TIP:

●

If a magnetic gear oil drain screw is
equipped, remove all metal particles from
the screw before installing it.

●

Always use new gaskets. Do not reuse the
removed gaskets.

4.

Remove the oil level plug and gasket to
allow the oil to drain completely.

NOTICE:

Check the used gear oil after

it has been drained. If the gear oil is
milky or contains water or a large
amount of metal particles, the gear
case may be damaged. Have a
Yamaha dealer check and repair the
outboard motor.

[ECM00713]

TIP:

For disposal of used oil, consult your Yamaha
dealer.
5.

Put the outboard motor in a vertical posi-
tion. Using a flexible or pressurized filling
device, inject the gear oil into the gear oil
drain screw hole.

1. Gear oil drain screw
2. Oil level plug

ZMU02064

2

1

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

0.250 L (0.264 US qt, 0.220 Imp.qt)

ZMU02065

U63V2DE0.book Page 47 Monday, February 22, 2010 9:00 AM

«
...
50
51
52
53
54
...
»

Содержание 9.9F































































Отзывы:

Нет отзывов

Похожие инструкции для 9.9F

Бренд: Yamaha Страницы: 87

Бренд: JETWAY Страницы: 44

Бренд: Quick Страницы: 24

STEVAL-ISB042V1

Бренд: ST Страницы: 26

Бренд: Vox Страницы: 23

Бренд: ASROCK Страницы: 257

Бренд: IEI Technology Страницы: 198

Бренд: MSI Страницы: 126

Бренд: Gigabyte Страницы: 88

Бренд: IEI Technology Страницы: 12

Бренд: TYAN Страницы: 54

Бренд: TYAN Страницы: 62

Бренд: TYAN Страницы: 117

Бренд: DFI Страницы: 79

Бренд: DFI Страницы: 97

Бренд: DFI Страницы: 108

Бренд: DFI Страницы: 121

Бренд: DFI Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды