Yamaha 9.9F Скачать руководство пользователя

Страница: 51 / 62

Maintenance

●

Check the propeller shaft oil seal for dam-
age.

EMU30662

Removing propeller

EMU29197

Spline models

Straighten the cotter pin and pull it out us-
ing a pair of pliers.

Remove the propeller nut, washer, and
spacer (if equipped).

WARNING! Do not

use your hand to hold the propeller
when loosening the propeller nut.

[EWM01890]

Remove the propeller, washer (if
equipped), and thrust washer.

EMU30672

Installing propeller

EMU29234

Spline models

NOTICE

ECM00501

Make sure to use a new cotter pin and
bend the ends over securely. Otherwise,
the propeller could come off during opera-
tion and be lost.

Apply Yamaha marine grease or a corro-
sion resistant grease to the propeller
shaft.

Install the spacer (if equipped), thrust
washer, washer (if equipped), and pro-
peller on the propeller shaft.

NOTICE:

Make sure to install the thrust washer
before installing the propeller. Other-
wise, the lower case and propeller
boss could be damaged.

[ECM01881]

Install the spacer (if equipped) and the
washer. Tighten the propeller nut to the
specified torque.

Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

NOTICE:

Do not reuse the cotter pin.

Otherwise, the propeller can come off
during operation.

[ECM01891]

1. Cotter pin

2. Propeller nut
3. Washer

4. Propeller

5. Thrust washer

ZMU02877

Propeller nut tightening torque:

17.0 Nm (1.73 kgf-m, 12.5 ft-lb)

U63V2DE0.book Page 46 Monday, February 22, 2010 9:00 AM

Содержание 9.9F































































Результаты поиска

Содержание 9.9F

Отзывы:

Похожие инструкции для 9.9F

Бренды по названию

Популярные бренды

Yamaha 9.9F, Руководство пользователя

Результаты поиска

Содержание 9.9F

Отзывы:

Похожие инструкции для 9.9F

Бренды по названию

Популярные бренды