Yamaha 9.9F Скачать руководство пользователя

Страница: 46 / 62

Maintenance

EMU34446

Maintenance chart 1

TIP:

●

Refer to the sections in this chapter for explanations of each owner-specific action.

●

The maintenance cycle on these charts assume usage of 100 hours per year and regular
flushing of the cooling water passages. Maintenance frequency should be adjusted when op-
erating the engine under adverse conditions such as extended trolling.

●

Disassembly or repairs may be necessary depending on the outcome of maintenance
checks.

●

Expendable or consumable parts and lubricants will lose their effectiveness over time and
through normal usage regardless of the warranty period.

●

When operating in salt water, muddy, other turbid (cloudy), acidic water, the engine should
be flushed with clean water after each use.

The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

Item

Actions

Initial

Every

20 hours

(3 months)

100 hours

(1 year)

300 hours

(3 years)

500 hours

(5 years)

Anode(s) (external)

Inspection or replace-
ment as necessary

Anode(s) (cylinder
head, thermostat cov-
er)

Inspection or replace-
ment as necessary

Anodes (exhaust cover,
cooling water passage
cover, Rectifier Regula-
tor cover)

Replacement

Cooling water leakage

Inspection or replace-
ment as necessary

Cowling lock lever

Inspection

Engine starting condi-
tion/noise

Inspection

Engine idle
speed/noise

Inspection

Fuel filter (can be dis-
assembled)

Inspection or replace-
ment as necessary

Fuel line (High pres-
sure)

Inspection

Fuel line (High pres-
sure)

Inspection or replace-
ment as necessary

Fuel line (Low pres-
sure)

Inspection

Fuel line (Low pres-
sure)

Inspection or replace-
ment as necessary

U63V2DE0.book Page 41 Monday, February 22, 2010 9:00 AM

Содержание 9.9F































































Результаты поиска

Содержание 9.9F

Отзывы:

Похожие инструкции для 9.9F

Бренды по названию

Популярные бренды

Yamaha 9.9F, Руководство пользователя

Результаты поиска

Содержание 9.9F

Отзывы:

Похожие инструкции для 9.9F

Бренды по названию

Популярные бренды