Yamaha 9.9F страница 41 Скачать руководство пользователя | Manualshive

Страница: 41 / 62

background image

Operation

36

4.

To return the outboard motor to the nor-
mal running position, place the gear shift
lever in neutral.

5.

Place the tilt lock lever in the lock/down
position, then slightly tilt the outboard mo-
tor up until the tilt support bar automati-
cally returns to the free position.

6.

Slowly lower the outboard motor to the
normal position.

EMU28195

Cruising in other conditions

Cruising in salt water

After operating in salt water, flush the cooling
water passages with fresh water to prevent
them from becoming clogged. Also rinse the
outside of the outboard motor with fresh wa-
ter.

Cruising in muddy, turbid, or acidic water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
(see page 10) if you use the outboard motor in

acidic water or water with a lot of sediment in
it, such as muddy or turbid (cloudy) water. Af-
ter operating in such water, flush the cooling
passages with fresh water to prevent corro-
sion. Also rinse the outside of the outboard
motor with fresh water.

ZMU02048

U63V2DE0.book Page 36 Monday, February 22, 2010 9:00 AM

«
...
39
40
41
42
43
...
»

Содержание 9.9F































































Отзывы:

Нет отзывов

Похожие инструкции для 9.9F

Бренд: Aaeon Страницы: 132

Бренд: Aaeon Страницы: 50

Бренд: Intel Страницы: 89

Бренд: Nematron Страницы: 47

Бренд: JETWAY Страницы: 58

Бренд: MSI Страницы: 30

Бренд: Tadao Страницы: 3

Бренд: Intel Страницы: 74

Бренд: Gigabyte Страницы: 60

Бренд: Pegatron Страницы: 30

Бренд: Intel Страницы: 98

Бренд: DFI Страницы: 92

SX1211-11SKA868

Бренд: Semtech Страницы: 30

Бренд: Supermicro Страницы: 88

Бренд: Aaeon Страницы: 74

Бренд: Gigabyte Страницы: 20

NuMicro NuTiny-SDK-NUC505

Бренд: Nuvoton Страницы: 26

Бренд: JETWAY Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды