Yamaha 9.9F страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 62

background image

Components

16

To increase resistance, turn the adjuster
clockwise.
To decrease resistance, turn the adjuster
counterclockwise.

WARNING

EWM00040

Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to steer, which could result in an
accident.

EMU26262

Trim rod (tilt pin)

The position of the trim rod determines the
minimum trim angle of the outboard motor in
relation to the transom.

EMU30440

Tilt lock mechanism

The tilt lock mechanism is used to prevent the
outboard motor from lifting out of the water
when in reverse gear.

To tilt the outboard motor up, set the tilt lock
lever to the “

” (up) position. To tilt the out-

board motor down, set the tilt lock lever to the
“

” (down) position.

EMU26333

Tilt support bar

The tilt support bar keeps the outboard motor
in the tilted up position.

NOTICE

ECM01660

Do not use the tilt support bar when traile-
ring the boat. The outboard motor could
shake loose from the tilt support and fall.
If the motor cannot be trailered in the nor-
mal running position, use an additional
support device to secure it in the tilt posi-
tion.

1. Tilt lock lever

U63V2DE0.book Page 16 Monday, February 22, 2010 9:00 AM

«
...
19
20
21
22
23
...
»

Содержание 9.9F































































Отзывы:

Нет отзывов

Похожие инструкции для 9.9F

Бренд: Ublox Страницы: 23

Бренд: Gigabyte Страницы: 93

Бренд: Freetech Страницы: 48

Бренд: Texas Instruments Страницы: 14

TB360-BTC PRO 2.0

Бренд: Biostar Страницы: 59

Бренд: ISSC Страницы: 39

GA-H170M-HD3 DDR3

Бренд: Gigabyte Страницы: 44

Бренд: Kontron Страницы: 105

Бренд: Maxus Страницы: 59

Бренд: MSI Страницы: 126

Super 7 SY-5SSM

Бренд: SOYO Страницы: 86

Бренд: MSI Страницы: 92

PN1 SLI2 Extreme

Бренд: ECS Страницы: 62

Бренд: IEPC Страницы: 9

Бренд: IEI Technology Страницы: 43

Бренд: DFI Страницы: 185

Бренд: Gigabyte Страницы: 40

Бренд: Asus Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды