background image

Specifications and requirements

9

EMU33556

Installation requirements

EMU33566

Boat horsepower rating

WARNING

EWM01561

Overpowering a boat can cause severe in-
stability.

Before installing the outboard motor(s), con-
firm that the total horsepower of your out-
board motor(s) does not exceed the boat’s
maximum horsepower rating. See the boat’s
capacity plate or contact the manufacturer.

EMU40491

Mounting outboard motor

WARNING

EWM02501

Improper mounting of the outboard mo-
tor could result in hazardous conditions
such as poor handling, loss of control,
or fire hazards.

Because the outboard motor is very
heavy, special equipment and training is
required to mount it safely.

Your dealer or other person experienced in
proper rigging should mount the outboard
motor using correct equipment and complete
rigging instructions. For further information,
see page 18.

EMU34196

Propeller selection

Next to selecting an outboard motor, select-
ing the right propeller is one of the most im-
portant purchasing decisions a boater can
make. The type, size, and design of your pro-
peller have a direct impact on acceleration,
top speed, fuel economy, and even engine
life. Yamaha designs and manufactures pro-
pellers for every Yamaha outboard motor and
every application.

Your outboard motor came with a Yamaha
propeller selected to perform well over a
range of applications, but there may be uses
where a different propeller would be more
appropriate.
Your Yamaha dealer can help you select the
right propeller for your boating needs. Select
a propeller that will allow the engine to reach
the middle or upper half of the operating
range at full throttle with the maximum boat-
load. Generally, select a larger pitch propeller
for a smaller operating load and a smaller
pitch propeller for a heavier load. If you carry
loads that vary widely, select the propeller
that lets the engine run in the proper range for
your maximum load but remember that you
may need to reduce your throttle setting to
stay within the recommended engine speed
range when carrying lighter loads.
To check the propeller, see page 40.

EMU25653

Engine oil requirements

1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)

Recommended engine oil:

YAMALUBE 2-stroke outboard motor 
oil

ZMU04604

-

x

1

2 3

U6GD22E0.book  Page 9  Friday, January 13, 2023  10:22 AM

Содержание 2D

























































Отзывы: