Yamaha 2010 XVS1300AZ Скачать руководство пользователя страница 31

Страница: 31 / 92

INSTRUMENT AND CONTROL FUNCTIONS

4-15

NOTICE

ECA10701

Use only unleaded gasoline. The use
of leaded gasoline will cause unre-
pairable damage to the catalytic
converter.

EAU42750

Rider seat

To remove the rider seat

1. Insert the key into the seat lock,

and then turn it counterclockwise.

2. Lift the front of the seat up, and

then pull the seat off.

To install the rider seat

1. Insert the projection on the rear of

the seat into the seat holder as
shown.

2. Push the front of the seat down to

lock it in place.

3. Remove the key.

TIP

Make sure that the seat is properly se-
cured before riding.

1. Seat lock

2. Unlock.

1. Projection
2. Seat holder

U12C23E0.book Page 15 Tuesday, October 20, 2009 4:17 PM

Содержание 2010 XVS1300AZ





























































































Результаты поиска

Содержание 2010 XVS1300AZ

Отзывы:

Похожие инструкции для 2010 XVS1300AZ

Бренды по названию

Популярные бренды

Yamaha 2010 XVS1300AZ, Руководство пользователя

Результаты поиска

Содержание 2010 XVS1300AZ

Отзывы:

Похожие инструкции для 2010 XVS1300AZ

Бренды по названию

Популярные бренды